Are you worried about your Hyundai Santa Fe backup camera not working properly?
If this is something that concerns you, then our tips should come in handy. After all, a malfunctioning Santa Fe camera is a big deal. You need it for your parallel parking and also for preventing accidents on the road.
Once it’s out, it can get a bit tricky to navigate around when you park and keep yourself from harm while driving.
What can you do then about these Hyundai backup camera problems? Our quick and easy tips should help you out!
Hyundai Santa Fe Backup Camera Not Working
You have probably thought that your Hyundai Santa Fe back up camera installation was pretty seamless and done perfectly.
One day it’s working well then suddenly, it just fails to do its job. What gives?
If you are concerned about this issue, check out the following suggestions we have for you.
Blurry Image
Let’s talk about blurry or fuzzy images on your backup camera. If this is an issue that you encounter, it could require some troubleshooting to fix it up.
Supposing you see nothing but a black and white image. In this case, you may need to look into the connection and wiring. The most common culprit behind this problem is a faulty connection or some frayed wiring, which causes a static. This explains the black and white, blur and fuzzy images.
No Signal
Now, in addition to some fuzzy image quality, you may even notice that there is no signal at all in your camera.
If this is the problem you’re getting, then you may have to check the fuse and connection.
There are a few reasons behind this issue. For instance, if your camera relies on wifi, then you may simply need to rest the display or the camera. As another piece of advice, checking the fuses, as well as the camera’s power cables may also help. These are typically found behind your car’s trunk panel.
In some cases, the lack of signal is due to a frayed or blown wire. Thus, it does not connect anymore to the wifi.
On the other hand, with wired backup cameras, the problem can be linked to wiring concerns. Inspect the fuses and make sure that every key component is connected appropriately. Trace the wiring and check the quality to make sure there are no damages at all.
Sometimes, removing your dashboard display may be necessary. It is difficult and painstaking to do this, but it could be ideal to do when your display is hooked up in your dashboard.
Also, a reset is always advisable just to make sure this zero signal issue is not simply a glitch.
Black Screen
Another problem with a Hyundai Santa Fe backup camera not working is a black screen.
If this is the issue you have, then it could be the camera is not set up well. You may have to re-do your Santa Fe camera installation. Other times, a new camera may be the only solution if after re-installing the unit, it still fails to do its job.
Now, when there is no display, it may be due to some wiring problems. Be sure the camera is plugged into your car’s AUX dash cable. A poor connection, in addition to damages to the monitor could be the culprit.
However, if you are able to power the display on, yet there is still no signal, then it could be a camera problem. If there are damages to the unit, then a replacement is your only bet.
Read this post: Hyundai Santa Fe Bluetooth Problems & Common Fixes You Can Try
Final Thoughts
It can be quite a hassle when your Hyundai Santa Fe backup camera is not working.
You depend on it for comfort and convenience in driving since it helps you to navigate the road, park, and keep yourself out of danger.
However, certain issues are inevitable to arise such as a no signal, fuzzy display, or the dreaded black screen in the unit.
Be sure to try our troubleshooting tips above before you consider buying a new camera. Sometimes, it can be resolved with a simple reinstall or by resetting the camera if it is a wireless unit.But if all else fails to work, then you may be well on your way to replacing your defective unit and swapping it with a newer one. Then, you can ensure your safety with a camera that actually works and does the job.
Is there a video that shows you the steps? (step-by-step?). [I don’t know where the trunk panel is, or where the fuses are].
Hi Nancy, The trunk panel on a Hyundai Santa Fe is typically located at the back of the vehicle, inside the trunk area. It covers the spare tire and provides access to various components such as the battery, fuse box, and wiring. To access the fuse box, you’ll need to remove the trunk panel. The specific location of the fuse box may vary depending on the model year and trim level of your Santa Fe, but it is usually located near the bottom of the trunk panel.
How do you reset the back up camera on a 2021 Sane Fe
Hi Jerry,
To reset the backup camera on a 2021 Hyundai Santa Fe, you can try the following steps:
– Turn on the ignition and start the vehicle.
– Locate the touchscreen display in the center console of your Santa Fe.
– Look for the settings menu on the touchscreen display. It is usually represented by a gear or wrench icon.
– Tap on the settings icon to access the settings menu.
– Within the settings menu, look for the “System” or “Camera” option. The exact naming may vary depending on the vehicle’s configuration.
– Select the “System” or “Camera” option to access the camera settings.
– Look for the “Reset” or “Restore” option within the camera settings. This option is used to reset the camera system.
– Tap on the “Reset” or “Restore” option and confirm your selection if prompted.
– Once the reset process is complete, exit the settings menu and test the backup camera to see if it is functioning properly.
If the above steps don’t work or if your Santa Fe’s interface is different, it is recommended to consult the vehicle’s owner’s manual or contact the dealership for specific instructions on resetting the backup camera.