Hyundai Clicking Noise Dash – What Causes This Problem?

So, you’re driving your vehicle when all of a sudden, you notice a concerning Hyundai clicking noise dash issue. What gives?

Perhaps you are worried that something may be going wrong with your vehicle. After all, your dashboard is not supposed to be creating such a strange sound… Right?

When there are peculiar noises from your car, it is quite normal to be concerned about it. And when you do hear these sounds, it is just right to do some investigation to make sure nothing serious is going on.

If you are experiencing this issue with your dashboard, let’s go ahead and find out just why it is happening and what can be done about it.

hyundai clicking noise dash

Hyundai Clicking Noise Dash – A Big Problem?

First of all, it is not at all normal for your dashboard to produce some rattles, squeaks and clicking noise. When you encounter these, it means that there are problems to be addressed – and as soon as possible.

Just some of the common reasons why these noises occur include an issue with your door stepper motor, loss of calibration to your heater control, as well as relay issues. It is also possible that your air condition system has some damages, which is why these clicking sounds occur.

We’ll discuss these common causes more in the next section.

Common Causes Of Clicking Noise On The Dashboard

As we have mentioned, there are many reasons why clicking sounds may be heard on your dashboard. Here they are:

1. Heater Motor Problemư

Your car’s HVAC system is important for keeping your vehicle’s optimal temperature. It regulates all components impacting the heating and ventilating in your car. But it also requires the right blend door posture reading, so it can perform its job well.

However, there are instances when degrees are miscalculated. When this happens, an erratic activation of the motor occurs. This is why it may cause some noises on your dashboard. A simple fix is by recalibrating the heater motor. Moreover, you can also look into addressing the blend door position if this also contributes to the problem with your heater motor.

Many factors cause the loss of blend door locales such as flatcar battery, disconnected battery, faulty stepper motor, and a disturbed stepper motor that has not been recalibrated.

When calibrating heaters, you need to start by turning the ignition on and then turning it back off. Next, remove your fuse from the HVAC system for just a minute. Afterwards, you can turn the ignition on, which means the system is now in its recalibration mode.

To calibrate, turn the ignition back on, start your engine and that’s about it. If you notice the issue does not resolve itself, you can check the stepper motor for issues.

2. Problem with the Relay

Your car has an electric equipment requiring many circuits, control modules and relays. The relay is a mechanical and electrical tool that controls loaded circuits. This is utilized in many components such as starter motors, wipers, power seats, lights, horns, and circuits. To check for a faulty relay, you should check for a rattling sound.

When the source of the issue is a faulty relay, then it needs a replacement. It is only a matter of pulling the old one out and replacing it with a new one. You should be able to do this yourself with the help of your car’s manual or a quick visit to the mechanic.

3. Stepper Motor Issues

This electric motor is designed to move in incremental motions. This converts digital pulses and turns them into a mechanical shaft motion. It creates a discrete and angular rotation where the magnitude is uniform, and this is required for the supply of the DC sequential switching.

Eventually, the stepper motor may malfunction and become unable to blend the car door. Thus, dashboard noises can be heard. If you suspect that the problem is with your stepper motor, you can diagnose the problem with a scan. A fault code should appear if the culprit is your stepper motor and you should be able to locate and identify the fault.

The quickest way to resolve this issue with a stepper motor is by getting it replaced. This way, you can address the problem with this component while fixing the clicking noise dilemma.

Read More: Hyundai Horn Doesn’t Beep When I Lock The Car

Bottom Line

A Hyundai clicking noise dash dilemma is worrisome since any sound can be a sign of failure or future issues. So, if you notice this sound in your dashboard, it is best to conduct a thorough inspection of areas in your car that may be causing these problems. We hope that our tips have been helpful in allowing you to locate and fix the problem once and for all.

Leave a Comment